View Cart
Hardware and Tubing
« Return to Product Categories
High Temp Tubes and O rings
|
Silicone O ring Thin 3/4" x 7/8" |
$1.25 |
USA FDA Approved. Thin wall Silicone O-Ring. Works great for 1/2" NPT fittings. Listed by the National Sanitaton Foundation. (NSF 51)
.812" id x .139" c/s
|
|
Silicone O-Ring (Thick 11/16" ID x 1" 3/16" OD) |
$1.25 |
USA FDA Approved Silicone O-Ring 30* 5.7mm Thick wall, works great for 1/2" NPT fittings. Listed by the National Sanitaton Foundation. (NSF 51).Price is each.
|
|
Tubing - Silicone (3/8" ID) High Temp |
$3.50/ft |
FOR LOW PRESSURE / HIGH TEMPERATURE APPLICATION Able to withstand extreme temperature variations from -100F to 500F. Odorless, tasteless and inert Translucent natural color for visual contact with flow of product Made from FDA sanctioned ingredients Excellent bend radius permits installation into restricted spaces without impeding flow NSF certified
|
|
Tubing - Silicone 1/2" High Temp |
$3.50/ft |
FOR LOW PRESSURE / HIGH TEMPERATURE APPLICATION Able to withstand extreme temperature variations from -100F to 500F. Odorless, tasteless and inert Translucent natural color for visual contact with flow of product Made from FDA sanctioned ingredients Excellent bend radius permits installation into restricted spaces without impeding flow NSF certified
|
Pumps
|
Chugger SS Center inlet pump |
$239.95 |
The Chugger lineup of pumps represents a great value for an even better price. These pumps are workhorses in the brewery. Featuring a robust flow rate of 7 gpm, and a magnetic drive designed to handle back-pressure, these pumps are a great addition to any brewing setup! The Stainless Steel Chugger showcases their molded Stainless Steel Pump Head. This stainless pump is a steal for the price, and we've been more than happy with the quality! Use this to ease transfers between kettles, cool wort via a counterflow chiller, or recirculate icewater for quicker chilling!
The Chugger pump has 1/2" mpt inlet and outlet, allowing easy configuration for any application! We recommend setting these pumps up with a Ball valve on the outflow side, this way you can throttle down the outgoing flow rate, allowing for more efficient sparges or cooling! The pump head can also be rotated 360° (in 90° intervals) allowing for even more customization!
Features:
- Stainless Steel Pump Head.
- Food Grade up to 250° F.
- 1/2" mpt inlet and outlet.
- High Flow rate of 7 gpm
- Max Head 18.9 ft
- 115v 55" cord and plug attached.
- 50/60 Hz, 1.4 amp
- 1/20 HP, 3500 RPM
- No more issues with crossthreading plastic heads or snapping off fittings.
|
|
Chugger SS inline pump |
$239.95 |
This Chugger Stainless Steel inline pump allows you to move hot wort with ease. The durable housing means you never have to worry about cracking the pump head when tightening your fittings. All the materials are FDA food compliant and the components are UL Recognized. This is the inline version where the inlet and outlet are 180º opposed to each other. This pump can handle liquids up to 250ºF, the inlet and outlet are both 1/2" male NPT and please note that you should never restrict the inlet of the pump, only the outlet.
Specifications:
Inlet 1/2" MPT Outlet 1/2"MPT Stainless Steel (Front Housing), Stainless Steel (Rear Housing), Teflon (Thrust Washer), CLEAR Silicone (O-Ring), Polysulfone (FDA) (Impeller) Max Flow 7 GPM 22.7 LPM Max Head 18.6 FT 4.1 M Power .04 HP .029 KW Electrical 115V 50/60HZ
Max Flow 7 GPM 22.7 LPM Max Head 18.6 FT 4.1 M Power .04 HP .029 KW
Can handle liquids of 250F Materials are FDA Food Compliant Components are UL Recognized DO NOT RUN DRY
|
|
Chugger SS inline replacememt pump head |
$89.95 |
With a stainless steel housing you never have to worry about cracking the pump head when tightening your fittings down. All the materials are FDA food compliant and the components are UL Recognized. This is the inline version where the inlet and outlet are 180º opposed to each other. Can handle liquids up to 250ºF. Inlet 1/2" MPT Outlet 1/2" MPT Stainless Steel (Front Housing), 316 Stainless Steel (Rear Housing), Teflon (Thrust Washer), CLEAR Silicone (O-Ring), Polysulfone (FDA) (Impeller) This is the replacement pump head assembly only and will fit Chugger or March 809 series pumps.
|
Quick Disconnects
|
Polysufone Male 1/2" MPT disconnect |
$14.95 |
1/2" male thread to male adaptor
|
|
Polysulfone Female Disconnect |
$27.95 |
1/2" barb to female adaptor; thumb button
|
Stainless Valves
|
2 Piece Ball Valve 1/2" |
$19.95 |
Full port Valve. 1/2" female NTP threads on both sides. Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 1/2" FPT on input and output side.
TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed
|
|
Blichmann 3 Piece Ball Valve |
$39.95 |
These are Blichmann's premium heavy duty 304 stainless steel valves for brewing, 3 piece style can be completely disassembled for thorough cleaning. Teflon seals are extremely durable and temperature resistant. Valve comes with 1/2" Female NPT threads on both sides, and slide lock to prevent accidental opening. Handle color may vary.
|
Stainless Steel Fittings
|
1/2" FPT to 1/2" Barb |
$5.95 |
|
|
1/2" MPT to 1/2" Barb |
$6.95 |
Stainless Steel 1/2" MPT (Male Pipe Thread) x 1/2" Barb Fitting.
|
|
Kettle Diverter for Boil Kettle |
$15.95 |
Designed to pull from the side of the kettle instead of the middle. This helps reduce trub from entering your fermenter. By adjusting the height you can also control how much wort you leave behind in the kettle. Has a 1/2 inch MPT fitting on the end, that screws into the inside coupler of our Heavy Duty kettles. Will only work if your kettle has a 1/2 inch FPT coupler on the inside of the kettle.
|
|
Plated Brass 3/8th inch tailpiece |
$3.95 |
Tailpiece (3/8")
PLATED BRASS TAIL PIECES (OVERSIZED) Vinyl Tubing - 3/8"
|
|
SS Close Nipple 1/2" thread x 1.5" long |
|
304 Stainless Steel Nipple 1/2" X 1/2" NPT (1.5" in length). Used to combine two fittings with 1/2" FPT threads.
|
|
Stainless Steel 1/2" (Grooved) Nut |
$1.95 |
Lock nut fitting (threads further on to male 1/2" npt than the non-grooved lock nuts). Recessed groove will fit our thin silicone o-ring. Great for weldless assemblies and applications.
|
|
Stainless Steel Close Nipple - 1/2" Male NPT x 1/2" Male NPT |
$4.95 |
304SS Stainless Steel Nipple 1/2" X 1" M NPT. Called a close nipple because there is no space between the threads. For connecting a 1/2'' ball valves or other devices to a union.
|
|
Stainless Steel Coupler - 1/2" Female NPT x 1/2" Female NPT |
$3.95 |
304SS Coupler with 1/2" NPT Female Pipe Thread. Couplers have threads for insertion from both sides. 1" 1/4" Length
|
|
Tailpiece 90 degree 3/16" barb |
$12.95 |
Tailpiece 90 degree 3/16" barb
|
Tubing
|
Tubing - Nylon Braided (1/4'' ID) - By the Foot |
$1.00/ft |
Braided nylon hose good to 150 PSI. Great for CO2 kegging systems.
|
|
Tubing PVC (1/4" ID x 1/2" OD ) by the foot |
$.75/ft |
Special dual durometer construction combines a low extraction inner contact surface with a flexible outer layer for excellent kink resisitance and taste protection properties. No-foam, super smooth bore. Super flexible even when cold. Crystal clear. Odorless, tasteless. The thick wall on this also makes it great as gas hose on kegging systems.
Sold by the foot
|
|
Tubing PVC - Beer Line (3/16"ID x 7/16"OD) by the foot |
$.75/ft |
Brewery Approved vinyl hose,this vinyl hose meets or exceeds all the rigid demands for draft beer dispensing systems. Draft beer hose that meets the brewery’s criteria has passed through a series of quality tests, which include taste and odor evaluations. This vinyl tubing remains flexible and durable at recommended temperatures and pressures. It will not rot, swell, or dry out and is unaffected by normal cleaning compounds. 3/16" I.D. - Use for most direct draw applications where the distance between the keg and the faucet is less than 6’. Also used as "choker" behind faucet spliced to larger I.D. trunk lines.
|
« Return to Product Categories